LOGIC GATE | XOR GATE | BUCKET OF PROJECTS

By -

 


XOR Gate


XOR or Ex-OR gate is a special type of gate. It can be used in the half adder, full adder and subtractor. The exclusive-OR gate is abbreviated as EX-OR gate or sometime as X-OR gate. It has n input (n >= 2) and one output.

XOR gate
tutorialspoint.com

Logic diagram

XOR Logical Diagram
tutorialspoint.com

Truth Table

XOR Truth Table
tutorialspoint.com

XOR Gate IC

As we seen above lets do in IC (7486)


circuits-diy.com


  • Red wire is the Vcc / Power / + wire
  • Black wire is the GND / Ground / - wire
  • Green wire is the Red LED power wire
  • Yellow wire is the input wire
  • Orange wire is the Output wire

1) When the input both are 0 output will 0



2) When the inputs are 0 and 1 output will 1


3) When the inputs are 1 and 0 output will 1

4) When the input both are 1 output will 0


Comments

Post a Comment

Popular posts from this blog

THE SG90 SERVO MOTOR WITH AN ARDUINO

By -
Image
Hi guys, today, I will show you how to use a servo motor with an Arduino. This tutorial is ideal for beginners because it is easy and it gives them the foundation to build interesting projects like robots for which servos are commonly used. Servo motors are high torque motors which are commonly used in robotics and several other applications due to the fact that it’s easy to control their rotation. Servo motors have a geared output shaft which can be electrically controlled to turn one (1) degree at a time. For the sake of control, unlike normal DC motors, servo motors usually have an additional pin asides the two power pins ( Vcc and GND ) which is the signal pin. The signal pin is used to control the servo motor, turning its shaft to any desired angle. For this tutorial, we will be using the popular SG90 servo motor and our goal will be to rotate the servo motor from one end to the other. Servo’s have high current requirement so when using more than one servo motor with the Arduino,
Read more

KUMAR ANADEN AND HE'S GUINNESS WORLD RECORDS | BUCKET OF PROJECTS

By -
Image
www.channelswimmingdover.org.uk      Kumar anadan was born on 1943 in Valvettithurai, Jaffna. He was graduated in University of London. He obtained Bachelor of Laws degree in Sri Lanka. He was an Attorney at Law by profession.       He was a holder of Guinness Worlds Records and he has many records. One of the famous records is Swimming the Palk strait from Sri Lanka to India and comes back within 51 hours, in the year 1971. These are some other records Non-Stop water treading for 80 hours at Chennai, Standing with one leg for 33 hours, Non-Stop dancing, Ball punching for 136 hours, etc. So, people were called him as “Aalikumaran Anaden” .       Once he met with a motor vehicle and hospitalized for 6 months. He died on 6 August 1984 while he attempting to swim the English Channel during collapse.  
Read more

IMPORTANCE OF READING | BUCKET OF PROJECTS

By -
Image
      A whole man is made by reading. because, it’s provided many information and experience for us from all over the world. And improve our language and creativity also. How exercise maintain our body heathy as well as reading maintain our mind healthy.       Julius Caesar said that if there any man who reads 1000 books, he is my guide. “I did not want freedom if there any books in prison” said Nelson Mandela. Albert Einstein said “ human best invention is book”.The news reporter ask "If you are gone alone, what will you do?" Jawaharlal Nehru said that he would live happy with books. So, famous people who are disappear from world, gained victory through reading books.       Finally, we can say that reading is very important and a most valuable thing over the world.
Read more

How to Draw a Rectangle using Pygame

By -
Image
What is Pygame? Pygame is a Python library designed to develop video games. Pygame adds functionality on top of the excellent SDL library. This allows you to create fully featured games and multimedia programs in the Python language. The Functions We Need! pygame.display.set_mode() : This function is used to initialize a surface for display. This function takes the size of the display as a parameter. pygame.display.flip() : This function is used to update the content of the entire display surface of the screen. pygame.draw.rect() : This function is used to draw a rectangle. It takes the surface, color, and pygame Rect object as an input parameter and draws a rectangle on the surface. Example 1:   Drawing a rectangle and filled it with blue color. from pygame.locals import * def main (): pygame.init() DISPLAY=pygame.display.set_mode(( 500 , 400 ) , 0 , 32 ) BLUE=( 0 , 0 , 255 ) pygame.draw.rect(DISPLAY , BLUE , ( 200 , 150 , 100 , 50 )) while True : for event
Read more

Arduino - Ultrasonic Sensor

By -
Image
The HC-SR04 ultrasonic sensor uses SONAR to determine the distance of an object just like the bats do. It offers excellent non-contact range detection with high accuracy and stable readings in an easy-to-use package from 2 cm to 400 cm or 1” to 13 feet. The operation is not affected by sunlight or black material, although acoustically, soft materials like cloth can be difficult to detect. It comes complete with ultrasonic transmitter and receiver module. Components required Breadboard x 1 (optional) Arduino Uno R3 x 1 Ultrasonic Sensor (HC-SR04) x 1 Jumper x 4 (Female-Male) Procedure Follow the circuit diagram and hook up the components on the breadboard as shown in the image given below. Ultrasonic Sensor 5V -  Arduino VCC Ultrasonic Sensor GND - Arduino GND Ultrasonic Sensor Trigger Pin - Arduino Pin 7 Ultrasonic Sensor  Echo Pin -  Arduino Pin 6   Sketch Open the Arduino IDE software on your computer. Coding in the Arduino language will control your circuit. Open the new sketch Fi
Read more

LOGIC GATE | XNOR GATE | BUCKET OF PROJECTS

By -
Image
XNOR Gate XNOR gate is a special type of gate. It can be used in the half adder, full adder and subtractor. The exclusive-NOR gate is abbreviated as EX-NOR gate or sometime as X-NOR gate. It has n input (n >= 2) and one output. www.tutorialspoint.com Logic diagram www.tutorialspoint.com Truth Table www.tutorialspoint.com XNOR GATE IC As we seen above, lets do using IC ( 7486 ) . Unfortunately,  XNOR GATE   IC is not in "Tinkercad" circuit simulation. So I'm going to mix XOR GATE + NOT GATE , as a result output will be same as XNOR GATE. Red  wire is  VCC  /  Power  /   +   wire Black   wire is  GND  /  Ground  /  -  wire Green  wire is the Red LED power wire Yellow  wire is the  input  wire Purple wire is the  Output  wire ( XOR GATE ) Orange  wire is  Output  wire ( NOT GATE ) 1)  When the   input both  are 0   output  will   1 2) When the   input  are  0  and  1   output  will 0 3) When the   input  are   1  and  0   output  will 0 4) When the   input both ar
Read more

Scratch - How to Change the Size of Sprite According to the Loudness

By -
Image
How to Change the Size of Sprite According to the Loudness Hello guys. In this blog we are going to see about changing sprite size according to the loudness input given to the microphone  Coding with Blocks 1) Lets place " when flag clicked " Block from " Events panel ". The " when flag clicked " Block triggers the Blocks/Block code connected to it below. 2) Now lets place " forever " Block from " Control " panel. The Blocks/Block inside the " forever " Block will run continuously.  3) Now lets place " set size to _ " Block from " Looks ". The " set size to _ " Block sets the size of sprite for giving value, here cat is the sprite. Play around by changing the value of it's size. Note - " forever " is used here to change the value of " set size to_ " Block continuously. It will be needed in 4th step and 5th step. 4) Now drag and drop " _*_ " Block inside " set
Read more

LOGIC GATE | NOR GATE | BUCKET OF PROJECTS

By -
Image
  NOR Gate A NOT-OR operation is known as NOR operation. It has n input (n >= 2) and one output. www.tutorialspoint.com Logic diagram www.tutorialspoint.com Truth Table www.tutorialspoint.com OR GATE IC As we seen above, lets do using IC ( 7402 ) components101.com Red  wire is the  Vcc  /  Power  /   +   wire Black  wire is the  GND  /  Ground  /  -  wire Green  wire is the Red LED power wire Yellow  wire is the  input  wire Orange  wire is the  Output  wire 1) When the   input  both are  0   output  will  1 2) When the   input  are  0  and  1   output  will 0 3) When the   input  are  1  and  0   output  will 0 4) When the   input both are 1  output  will 0 Other Gates AND GATE OR  GATE NOT  GATE NAND GATE XOR  GATE XNOR  GATE
Read more

Arduino - Led Blink

By -
Image
  This is a simple project using Arduino. It would  enrich your knowledge about Arduino. You’re going to program your first  Arduino project starts with LED. Components required You will need  following components -      Breadboard x 1     led x 1 ( any color )     220Ω / 330Ω Resistor x 1     Jumper x 2  ( Male - Male)     Arduino Uno x 1 ( Any Arduino board can be used ) Procedure Follow the circuit diagram and hook up the components on the breadboard as shown in the image given below. Connect the positive terminal of the LED to 8th pin in Arduino board after adding resistor to negative terminal of the LED then connect the end of the resistor to GND of the Arduino board.    Note − To find out the polarity of an LED, look at it closely. The shorter of the two legs, towards the flat edge of the bulb indicates the negative terminal.    Sketch Open the Arduino IDE software on your computer. Coding in the Arduino language will control your circuit. Open the new sketch File by clicking New
Read more